ARM: Does uVision5 Simulator supports CAN peripheral Simulation?
Hi Everyone I am trying to run a simple CAN application using the simulator of Keil ARM-MDK V5.22 (uVision 5). But I have doubts about whether Keil uVision 5 supports simulation of CAN peripheral of...
View ArticleARM: STM32L053 Debugger automatically executes (2 Replies)
I have a target board with only a few signals. I have created a very simple Blink LED project from the CubeMX software. It imports into Keil, compiles, and downloads to FLASH. But when it hits the...
View ArticleARM: Debug on real board stops immediately.
I am currently enrolled in EDX online course and started with the first assignments, however while carrying out the debug phase the simulator reverts to editing mode. I am using Windows 10 machine and...
View ArticleARM: LED not working as programmed (2 Replies)
I created a program to glow LED once a flag is set. And until a switch is pressed, the LED should continue to glow. The switch is in pull up mode. But the LED is not glowing at all. Please guide....
View ArticleARM: How to run two process simultenously in a single core
Hi, I need to run 2 functions or process simultaneously, like in 2 function, first function will be running continuously and when it's time to run the second function, it runs initially and later on...
View ArticleARM: While running keil in debug mode, it is stopping. (1 Replies)
I am using MCU Cortex-M4 and running keil on simulator. In debug mode while running it is getting stopped at _sys_open function in call stack but in text editor arrows showing at SystemInit after...
View ArticleARM: How to avoid BKPT 0xAB instruction (1 Replies)
I am using MCU Cortex-M4 and running keil on simulation. while running keil in debug mode, code is stopping at BKPT 0xAB instruction and we have to re initialize run to continue like break point. I am...
View ArticleARM: botloader hid exmaple. (3 Replies)
I see lots of good usb examples in the pack installer, but is there a bootlaoder for usb example anywhere?
View ArticleARM: usb middle-ware alternatives. (4 Replies)
We purchased a lic. with ST for MDK Plus Single User one year and now we learned the USB examples are considered middle-ware. My management team is not keen on another 2k a year. Is the limitation...
View ArticleARM: Where to start? (1 Replies)
Hello, I am currently working on a project and have been given an MCB4300 evaluation board with a LPC4357 microcontroller. I have got the blinky example loaded and working on the board, but I do not...
View ArticleARM: How to truncate a file ?
We are using Keil 5.22 and RTL library on a LPC1768 board on which we have an SD card interface. All the usual file access works, fopen(), fprintf(), fdelete(), frename() etc... However I can't find...
View ArticleNone: NO ULINK DEVICE FOUND keil version 4.6
I have an old ULINK2-ME device that the computer will connect to that device. I got a new one that is exactly the same but when I try to program I get the error "NO ULINK DEVICE FOUND". I don't get...
View ArticleARM: change pack installer to use 205?
Is there any way to make the pack installer to use my selected chip? Every example I make is set up for the stm32f207 and I have the 205 selected. This works for the most part but all the pin names...
View ArticleARM: Download KEIL uVision 4 (6 Replies)
Hi! Please tell me from where can I download KEIL uVISION 4 and other older versions if not here on the official website. Thanks
View ArticleC51: Clean project in a command line (2 Replies)
We use uv4 -b <<project>> to build the project in a batch environment. we try to perform uv4 -c << project >> for clean. Clean does not appear...
View ArticleARM: usb hid exmaple, how to use this? (1 Replies)
I loaded the usb hid example from the pack installer and everything compiles and flashes fine. When I use my core205 board via usb no HID is loaded. Also I searched thru all the file and can not find...
View ArticleNone: Access GPIO
How can I access the GPIO on my BMD 300 (control them using basic methods like pinMode, digitalWrite? Do I need to download a new library to include in the IDE?
View ArticleARM: Ulink Pro ETM Trace on LPC4078
Hi, My customer is using Ulink Pro for LPC4078 ETM trace, while they met an issue that the trace debugger failed to communicate with LPC4078 when its system clock is over 60M(Under 60MHz, it is ok)....
View ArticleARM: Flashing program code in RAM using keil software
Hey ARM/Keil Team, I have been using keil mdk with evaluation board of LPC2148 for testing and training purposes but unable to get any info to use RAM so program goes in RAM and works from there. i...
View ArticleARM: Total stack size and memory of a program in Keil (1 Replies)
Is there a way to determine the total stack size available and consumed by the variables in the program? Same for the memory i.e total available and consumed by the program? It seems there's a stack...
View Article